107Listing ID: 239598GET EQUIPMENT FINANCING
Cannabis & Hemp Insurance
Price : $800,000
Status : ACTIVE
Sale Type : Cash, Financing, Owner Financing
Company Name : Grace Equipment Specialists LLC
Phone : 401-742-4812

3.0 Four (4) Multi Screw Receiving Pit Systems
* 3.1 Four (4) 24” Augers in a common trough
* 3.2 14’x14’ square pit opening in the floor above
* 3.3 9’x9” from centerline of pit centerline of outlet
* 3.4 Four (4) Shaft mount direct-drive gearbox
* 3.5 Four (4) 10 H.P. 230/460V, 60Hz @ 1750 RPM, TEFC 3.6 Anti-jam & zero speed switches
* 3.7 Support legs to concrete floor to tunnel

4.0 DRAG CHAIN CONVEYOR SYSTEM
4.1 Two (2) Dump Pit Bulk-Flo 18”x30” Chain Conveyors
1. 4.1.1 Width 30” x Height 18”
2. 4.1.2 Head Housing 3/8” mild steel
3. 4.1.3 Tail Housing 3/8” mild steel
4. 4.1.4 Side Panel Construction 1⁄4” mild steel
5. 4.1.5 Bottom Construction 3/8” mild steel
6. 4.1.6 Liner Construction NONE
7. 4.1.7 Cover Construction 1⁄4” mild steel
8. 4.1.8 Divider Plate Construction 3/8” mild steel
9. 4.1.9 Material Depth 15.1”
4.1.10 Conveyor Components Consisting of: (1) “Bulk-Flo” style non-flared head section with 29T (14.5 pitch) relief sprocket for
SB155 chain with 5 15/16” hubs & 5 15/16” DIA Dodge type E 4-bolt PB bearings
• • (1) “Bulk-Flo” style non-flared tail section with 29T (14.5 pitch) relief sprocket for SB155 chain with 4 15/16” hubs & 4
15/16” DIA Rex “ZT” Take-up bearing shaft drilling & tapped. Head & Tail shaft & Bearing Guards included
• • (1) 4B Components “M800” under speed motion monitor with “Whirligig Mag-Con” (Ship loose)
• • (1) Single take up section
• • (8) 10’0” intermediate sections
• • (1) 9’6” Intermediate section
• • (1) 11’-2 3/8” Intermediate sections with 60 degree, 120” radius curve up
• • (1) 7’3” Intermediate section
• • (1) 11’-4 1/16” Intermediate sections with 60 degree, 120” radius curve down
• • 279 Linear feet of single stranded SB155 carbon steel bushed chain, pins 525-654 BN, barrels 615-705 BN, assembled
with attachments on 18” spacing with standard 1⁄2” (13mm) UHMW flights with backing plates
• • (2) Custom feed-through inlet assembly’s 46”W x 96” L with a meting flange shipped loose
• • (13) Pairs of 12” Supports
• • (3) Inspection Doors 10”x20” mild steel inspection doors
• • (1) Gasket/seal package with red Hi-Temp RTV silicone
• • (1) Paint touch up kit
• • Single Shaft Mount Drive: Components Consisting of:
• • WEG 30 H.P. 230/460V, 60Hz @ 1750 RPM, TEFC, Energy efficiency
• • Dodge reducer
• • Motor mount
• • Reducer rod assembly
• • Reducer bushing
• • Sheaves, bushing, belt package
• • Expanded metal V-belt guard
• • Drive to extend on the RIGHT side
• • Two (2) Incline bulk-flo 18”x30” conveyor
• • Width 30” x Height 18”
• • Head Housing 3/8” mild steel
• • Tail Housing 3/8” mild steel
• • Side Panel Construction 1⁄4” mild steel
• • Bottom Construction 3/8” mild steel
• • Liner Construction NONE
• • Cover Construction 1⁄4” mild steel
• • Divider Plate Construction 3/8” mild steel
• • Material Depth 15.1”
• • Conveyor Components Consisting of: (1) “Bulk-Flo” style non-flared head section with 29T (14.5 pitch) relief sprocket for
SB155 chain with 5 15/16” hubs & 5 15/16” DIA Dodge type E 4-bolt PB bearings
• • (1) “Bulk-Flo” style non-flared tail section with 29T (14.5 pitch) relief sprocket for SB155 chain with 4 15/16” hubs & 4
15/16” DIA Rex “ZT” Take-up bearing shaft drilling & tapped. Head & Tail shaft & Bearing Guards included
• • (1) 4B components “M800” under speed motion monitor with “whirligig mag-con” (ship loose)
• • Single take up system
• • (9) 10’-0” (3048 mm) intermediate sections
• • 3’-0” (914 mm) intermediate sections
• • 13’-3 5/8” (4054 mm) intermediate sections with 72 degrees, 120” radius curve up
• • 6’-3” (1905 mm) intermediate sections
• • 13’-6 1/8” (4118 mm) intermediate sections with 72 degrees, 120” radius curve down
• • 4’-6” (1372 mm) intermediate sections
• • (1 ONLY) 331-Linear feet of single stranded SB155 carbon steel bushed chain, pins 525-654 BN, barrels 615-705 BN,
assembled with attachments on 18” spacing with standard 1⁄2” (13mm) UHMW flights with backing plates
• • (1 ONLY) 301- Linear feet of single stranded SB155 carbon steel bushed chain, pins 525-654 BN, barrels 615-705 BN,
assembled with attachments on 18” spacing with standard 1⁄2” (13mm) UHMW flights with backing plates
• • 1-Feed through inlet assembly: 20”W x 24”L
• • (15) pairs of 12” supports
• • (3) Inspection Doors 10”x20” mild steel inspection doors
• • (1) Gasket/seal package with red Hi-Temp RTV silicone
• • (1) Paint touch up kit
• • Single Shaft Mount Drive; Components Consisting of:
• • WEG 30 H.P. 230/460V, 60Hz @ 1750 RPM, TEFC, Energy efficiency
• • Dodge reducer
• • Motor mount
• • Reducer rod assembly
• • Reducer bushing
• • Sheaves, bushing, belt package
• • Expanded metal V-belt guard
• • Drive to extend on the RIGHT side
• • Two (2) Silo Fill Conveyor 30” x 26” chain conveyor
• • Width 30” x Height 26”
• • Head Housing 3/16” mild steel
• • Tail Housing 3/16” mild steel
• • Side Panel Construction 3/16” mild steel
• • Bottom Construction 3/8” Com. GRD. A.R.
• • Liner Construction NONE
• • Cover Construction #12 Ga. Mild steel

Contact Listing Owner
Cannabis & Hemp Banking
Related Listings